The 10 Best Reciprocating Saw of 2020 – Top Pics & Reviews

A reciprocating saw is a kind of machine-controlled saw in which the cutting effect is achieved by moving the push-and-pull blade.

This term is often used for the type of saw used in construction and demolition work. This type of saw, also known as hognose or Recip saw, has a sizeable wheel-like jigsaw and handle aligned so that the saw can be conveniently used on perpendicular surfaces. The standard design of this saw has a foot on the bottom of the blade, similar to the jigsaw.

It was challenging to reduce the best reciprocating saw, but someone had to do it. Reciprocating saws, also called reciprocating saws, reciprocating saws, or even saws – everything is a sharp and versatile hand saw that could cut wood, metal, masonry, fiberglass, and more. The return is that the cutting effect is achieved by reciprocating or pressing and pulling the blade.

There are many types of blades for these saws, each of which is designed for a specific task. The most common blades are carbon steel, but there is also high-speed steel, bicarbonate steel, carbide tip, carbide gravel, and diamond blades. It is best to use blade combinations for general use for DIY and individual blades for more extensive controls. The reciprocating saw landscape is evolving with better technology and higher performance.

Our Top Picks

1. Dewalt DC385

We chose this tool as the best option not only for the quality design but also for the Universal performance of this tool. With a full load and sharp blade, handle most heavy metal materials and other materials like wood and plastic accurately and quickly.

The four-position blade clamp allows for the comfortable position of the blade in four different directions, and the keyless blade change system makes changes a breeze – simply pull the lever on the front side of the saws, release the blade immediately and insert a new one.

Like all powerful saw, Dewalt DC385 base is made of durable plastic, which covers about 60 percent of these saws, and the release surface is made of non-slip rubber, which ensures a comfortable grip. The powerful variable-speed motor offers a speed of up to 3000 strokes per minute with a length of 1-1 / 8 inches. This tool is lightweight, portable, and handles very well and provides an excellent addition to the strength of your device’s Arsenal.

2. Dewalt DCS387P1 20 volt

Lightweight and compact, this 14.5-inch seven-pound saw makes it easy to cut in hard-to-reach areas. Exceptionally beautiful is čtyřpolohová terminal blade, which provides a more versatile position of the blade and allows you to rinse cut at awkward angles with the exchange of the blade without tools. This cordless saw includes a five-inch lithium battery, which was praised by consumers, who claim that it alone is worth the cost of the kit. Variable trigger speed with 2900 strokes per minute (SPM) and 1-1 / 8-inch stroke length provides faster-cutting speed with increased blade control and provides more accurate cuts.

Dewalt DCS387P1 includes a bright LED light that serves well in dark areas for greater visibility for a more accurate and safe cut. This kit comes with a convenient bag for secure storage and organization. As a compact reciprocating saw with so many features, this is our premium option.

3. BLACK + DECKER BDCR20B 20V

If you need a light saw that offers a robust cutting performance like no other, read on as you will be amazed by everything these saws offer. How battery-powered saws are going BDCR20B is ready to impress with increased battery life, and cutting on any type of surface in record time, adjustable in any material with a variable speed trigger.

It enables the user to manage and manipulate the speed based on the toughness of the application, which is itself a great feature for newcomers and professionals.

This versatile tool is a must for the workshop and offers up to 30% more work performance and is designed for extreme hot and cold temperatures. Shorter 7/8 inch stroke, these tools give you more accurate control for sensitive projects. Also, they can more and more restrict the region in which the conventional saw fit.

The lightest saber saws are known for their powerful vibration. Still, this Black & Decker model needs to be considered, including their damping technology, which significantly reduces vibration, provides more handling control, more comfort, and less user fatigue.

The Best Reciprocating Saw on the Market

1. Dewalt Bare-Tool DC385B Wireless

Dewalt Bare-Tool DC385B Wireless

This 18v wireless reciprocating saw is ready to cut through anything that gets in its way. For tasks that need to be built, rebuilt or demolished, this saw works like a ninja with a powerful variable-speed engine that drives up to 3,000 beats per minute and maintains an aggressive run time of 1-1/8 inches. The four-piece blade clamp allows for greater versatility at a limited distance and allows water to be washed away at almost any angle.

The reciprocating-effect clamp enables quick and easy blade replacement and safe, non-slippery rubber handles to increase handling control and reduce fatigue. DeWalt is still a trusted Soderstrom name and supports this product with a limited three-year warranty that applies to defective or manufacturing defects, as well as a one-year free service contract that covers the replacement of all used parts for regular use.

Why we like it

  • Fast and easy blade hunting
  • Non-slip comfort handle
  • One 1/8-inch length
  • Up to 3000 rpm
  • Weight: 5.8 lbs
  • Power source: Cordless
  • Running length: 1-1/8 inches

Our verdict:

This lightweight, portable reciprocating saw does well for any size of work, and it is versatile and convenient enough for use with metal, wood, plumbing, repair equipment, in tight reconnaissance areas, roofs, and more. Well built, this saw is a permanent and robust replacement for other reciprocating saws with many different types of blades that can be used.

2. DEWALT DCS387P1 20v

DEWALT DCS387P1 20v

With a total length of just 14.5 inches, this seven-pound saw is compact and lightweight, making it easy to cut in these hard-to-reach areas. Besides, the four-piece blade clamp offers better versatility and enables fishing at steep angles with tool-free blade changes.

Surprisingly robust for its size, this saw has a variable speed trigger that powers up to 2900 beats per minute, and has an impressive run the length of 1-1/8 inches for higher cutting speed. There is a swivel boot that also offers more control and versatility.

Why we like it

  • Fast and easy blade hunting
  • Non-slip comfort handle
  • One 1/8-inch length
  • LED light
  • Weight: 9.3 lbs
  • Power source: Cordless
  • Running length: 1-1/8 inches

Our verdict:

With an excellent rating of 4.7 out of five stars, this reciprocating is a big hit for consumers for its overall versatility, durability, and performance. We love the fact that it is so light and compact that it is effortless to maneuver and transport to different areas.

LED light is a practical feature, especially in darker and narrower regions where there isn’t enough lighting to see the work – it offers a safer and safer cutting experience.

3. BLACK-DECKER BDCR20B 20V

BLACK-DECKER BDCR20B 20V

Lightweight and sturdy Battery-free Black – Decker offers a tool-free blade replacement system for added comfort, with variable trigger speed and a swivel boot for more control that does the job faster and more efficiently to provide up to 30 percent more power.

The 7/8-inch blade is designed to provide greater accuracy and cutting control and less reflection than longer blades. Besides, Black and Decker go by providing damping technology to reduce vibrations. It contains a blade, and the battery is sold separately.

 Why we like it

  •  Blade replacement without tool
  •  Lightweight
  •  7/8-inch length
  •  Wireless
  •  Weight: 3.9 lbs
  •  Power source: Cordless
  •  Stroke length: 0.875 inches

Our verdict:

It is a wireless reciprocating saw that is still very powerful and holds a peak that will deliver up to 3000 beats per minute. The new damping technology ensures a pleasant smooth cut with less vibration. Secure handling makes it easy to handle this saw for almost everyone.

4. SKIL 9216-01 9 Amp

SKIL 9216-01 9 Amp

Thanks to a reliable and durable nine-amp amplifier that drives almost any type of material without seeds, this reciprocating saw is again a pleasant experience and guarantees high performance. Depending on the hardness of the project, users can manipulate and control the speed of the saw to provide a more controlled and safer cutting experience. Speaking of safety: This saw includes tool-free blade replacement for trouble-free replacement and counterweights, as well as a swivel leg that adds extra strength to work.

When it comes to comfort, there is a soft handle that facilitates handling while reducing fatigue. The manual supplied with this reciprocating saw is easy to understand which type of blade works best with which project – so this saw is ideal for beginners and professionals.

Why we like it

  • Light
  • Compact
  • Strong
  • Sustainable box
  • Weight: 7.2 lbs
  • Power source: Cord
  • Barrel’s length: 1,125 inches

Our verdict

We noticed the overall performance of these compact reciprocating saws. The high-performance engine does not discriminate. For our tests, this saw cut concrete, as well as it through the wood. This saw is not only reliable but also easy to use. It is an ideal complement to someone’s workshop.

5. DEWALT DWE304 10-Amp

DEWALT DWE304 10-Amp

This sturdy saw includes a 10 amp motor designed for heavy applications. There is a four-position terminal that allows greater versatility at a limited distance and allows water to be rinsed from almost any angle. There is also a sturdy boot to add more robustness at work, with a keyless lever clamped disc for simple blade replacement. With 2800 shots per minute, it also has a variable speed trigger for better control of the user, depending on what it is used.

The common materials for these reciprocating saws are wood, heavy metals, drawing, plaster, plastics, rubber, fiberglass, and composites. A limited three-year warranty supports this DeWalt tool.

Why we like it

  • Light
  • Variable speed control
  • Strong
  • Practical blade replacement
  • Weight: 7 lbs
  • Power source: CordedStroke
  • Length: 1-1/8 inches

Our verdict:

DeWalt made the cut fun again with all the powerful and versatile properties of this saw. Replacing the blades is easy to rework, just reciprocating the small lever, and this will immediately release the blade. The quality is excellent and does not seem to notice the difference between light wood and steel – it cuts both materials and butter.

6. Bosch RS7 – RAP10PK 11-Amp

Bosch RS7 - RAP10PK 11-Amp

As if the 11-ampere engine on this saw didn’t impress you enough, combine it with a compact and lightweight design and a better power-to-weight ratio in your class, and that will surely attract your attention. Even the edgiest reciprocating saw masters would have all the power, accuracy, and durability that this saw produces in the most challenging projects.

This reciprocating saw contains a set of 10-piece blades made of precision teeth and durable blade, designed for standard cutting and providing continuous performance in wood, wood with nails, and metals. There is a blade replacement without tools for quick and effortless removal and a soft ergonomic handle for comfort and reduced fatigue.

Why we like it

  • Improved power-to-weight ratio
  • Universal
  • Variable speed trigger
  • Set of 10 blades included
  • Weight: 11.09 lbs
  • Power source: Cord
  • Barrel’s length: 1,125 inches

Our verdict:

Bosch has considered all this when it comes to offering the most powerful, durable, and comfortable cutting experience. We love how the dual LED lighting system of this reciprocating saw illuminates the cutting surface for a safer overall experience. The blades work very well, easy to change, and overall this reciprocating saw worked impressively, and with the fact that it is a wireframe, there were no other concerns about how long the battery would last.

7. PORTER-CABLE PCC670B 20v

PORTER-CABLE PCC670B 20v

Porter-Cable is a trusted brand and known for its high-performance, powerful saw. Its reputation for its general versatility characterizes this reciprocating saw. Lightweight and compact, this reusable saw is ideal for more demanding work in the narrowest spaces.

With a high-performance engine and a one-inch running length, it’s designed for general suppliers, handymen, or changers, making it easier for everyone at any level of experience. There are a simple toolless blade system and a swivel boot that keeps the blade safe and accurate, and a variable speed trigger for better control.

Why we like it

  • Compact
  • Easily
  • Wireless charging
  • Variable speed
  • Weight: 4.6 lbs
  • Source of power: Cordless
  • Running length: 1 inch

Our verdict

This compact, wireless saw makes the cutting experience much more comfortable and fits into almost any tight spot, cutting with high power and precision. The ergonomic handle is soft and comfortable, and with less than four pounds, it’s a convenient saw for almost everyone to use effectively.

8. Milwaukee 6519-31 12 Amp Sawzall

Milwaukee 6519-31 12 Amp Sawzall

It offers world-class speed, durability, and performance with 0-3000 per minute and 1-1/8 inch driving time and 12 amp engine. There is a gear protection clutch that extends the life of the gearbox and engine due to high impact absorption, and the QUICK-LOK brake clamp is designed for rapid disk change without tools. The redesigned front handle of this reciprocating saw offers the ergonomics and comfort that is the best in its class.

Why we like it

  • High-performance engine
  • Reduced vibrations
  • Quick replacement without tools
  • Comfortable handle
  • Weight: 12 lbs
  • Power: With cable
  • Running length: 1-1/8-inch

Our verdict

It contains enough power, comfortable ergonomics, and one of the best brands, Milwaukee is a name you can trust with a range of reciprocating saws. Like the original Sawzall brand, this reciprocating saw is used by professionals and artisans for their reliability, durability, and strength.

9. Makita JR3050T 11 Amp

Makita JR3050T 11 Amp

This saw combines a powerful 11 amp engine with a weight of 7.3 pounds, making these saws to has excellent handling and performance. The speed goes up to 2800 SPM and has 1 1/8 inch reciprocating blades for an efficient and efficient cut, suitable for metal, wood, drywall, plastics, conversion, and demolition work. Also, there is an internal dust blower system that conveniently clears dirt when cutting to allow for better visibility and more precise cuts, and replacing the toolless blade with stout footwear provides rapidly evolving comfort.

These saws are certainly designed to ward off dirt and provide a longer saw life with all ball and needle bearings and a protective rubber shoe that seals the engine and bearings from the outside.

Why we like it

  • Strong
  • Easily
  • Well-designed
  • Universal
  • Weight: 7.1 lbs
  • Power: With cable
  • Running length: 1-1/8-inch

Our verdict

In almost every application, these saws do their job well. Makita goes over by not only making this 11 amp engine but offering many practical and safe functions and extending its lifespan with its overall design. This reciprocating saw is easy to process and does professional work at a standard cost and cannot be beaten for its durability.

10. Hitachi CR13VBY 12-Amp

Hitachi CR13VBY 12-Amp

As a leading provider of power tool technology, Hitachi is once again amazed by its revolutionary protection against user vibration. This UPV technology reduces vibration by more than 65 percent and uses a counterweight mechanism that absorbs shocks, increases performance, and delivers better, more excellent cuts.

Why we like it

  • Strong
  • Easily
  • Well-designed
  • Universal
  • Weight: 9.7 lbs
  • Power: With cable
  • Running length: 1-1/4-inch

Our verdict

With almost all applications, this saw has done its job well. Makita goes over by not only making this 11 amp engine but offering many practical and safe functions and extending its lifespan with its overall design. This reciprocating saw is easy to process and does professional work at a standard cost and cannot be beaten for its durability.

Guide for buyers

What is a reciprocating saw used for?

If used acolyte properly, the answers to the saws can be a lot of fun, and they could just turn you into a demolition junkie. For example, a demolition project that would normally take many hours of fighting and sweat to break down with a crowbar becomes much more straightforward with a reciprocating saw, which instead cuts through all the materials in a quarter of the time—Windows, walls, sanitary facilities, doors, etc.

Also referred to as the “gateway tool,” this reciprocating saw is what you own when you finally do a severe DIY deal and have been around a hard knock block several times. This is a tool that sets you apart from newcomers. Reciprocating saw is not for exceptional craftsmanship. It is used for dismantling and managing more extensive projects.

It is designed to enter these narrow areas with an exposed blade and different positioning for precise angle cutting. Several types of a blade are used with a reciprocating saw, depending on the project and the cutting material. For example, a fine-tooth blade, which resembles a hack saw, is used for cutting through metal pipes and nails; the rough blade is for cutting wood; super-coarse blade on plaster; and a “toothless” blade for cutting stones – these are specially coated with carbide grinding grain.

However, you also don’t have to be uber-picky if you choose the best blade. Surely you can use a nail-cutting blade to cut through, for example, a badge on belt and plywood. The more you are familiar with your saw ability, the more confident you are while choosing a blade for a specific task. Most blade types are available in standard six-inch lengths, but smaller ones are available, such as jigsaw types.

There are also 12-inch blades that are beneficial for getting into deep crevices or cutting thick wood. Blades are hard, but not indestructible. They are disposable and should be replaced if you find that the work is slowed down due to a blunt blade. There are bi-metal blades attached to steel teeth that remain flexible longer and exceed standard carbon steel blades with faster cutting but cost more.

To extend the life of your blade, they can be hammered flat and reused at a slope. You can try a little trick by cutting off the tip at an angle with some snippets of tin – with a sharper blade (make sure you wear protective goggles on it).

There are also several techniques you can use that further extend the life of your blades:

  • Make sure you put the right pressure on the saw – and don’t worry, you learn from experience. It’s a complex balance between knowing when to settle down and when you can turn on.
  • Make sure your reciprocating saw is firmly on the surface of the material, which reduces vibration and increases cutting speed.
  • Using the swing movement up and down with a saw will undoubtedly increase the cutting speed.
  • If you need to get close to the cut nails that are under the lower coatings, tilt the blade so that the teeth are in the clamp, then cut to make sure you don’t cut into the surfaces.
  • Although reciprocating saws are relatively safe during use, they remain dangerous saws, and standard safety regulations still need to be followed.
  • Before you cut, know where power lines, heating holes, and plumbing pipes are in your area.
  • When replacing the blades, always disconnect the saw first.
  • Be aware of the prosthesis – when the blade comes into contact with the material, and the curls are sharp – that could get you out of balance. Be especially aware of this when sitting on a telescopic ladder. This can happen even when cutting pipes or wood.
  • Blade generates heat when cutting. Do not touch the blade immediately after the saw, allow to cool before replacing the blade.

Are reciprocating saw blades universal ?

The short answer is yes. Reciprocating saw blades are part of all standard reciprocating saws on the market. The length of saw blades varies from three to 12 inches, which determines the depth of the cut, while the width and thickness assess the stability of the blade.

Each saw blade for the reciprocating saw is designed for a specific task and therefore differs in size, material, number of teeth, chamfer, thickness, and angle. By breaking this:

  • Carbon steel blades are one of the most common and cost-effective blades, suitable for cutting softwood, but are quickly blunted with hardwood and other hard materials.
  • High-speed steel blades (HSS) are more expensive than carbon steel, but also much harder, so they prune hardwood without blunting so quickly. It is the right choice as a versatile, durable blade that lasts five times longer than carbon steel.
  • Two-metal blades are even harder and last, on average, up to ten times longer than a carbon steel blade.
  • Carbide blades are the most common type of two-metal saw blades and are best suited for particularly demanding cuts.
  • Carbide blades are more abrasive and are made of harder materials such as brick, marble, ceramics, and fiberglass. As the most common type of grinding reciprocating wheel, the coatings range from medium to heavy.
  • Diamond blades have real diamonds inserted into the ends and are used to cut through glass, ceramics, and concrete. Six types of blade are made for specific tasks:
  • The rushing blade has a giant esophagus (the area between the teeth) and several teeth that remove the wood quickly and efficiently and form a rough cut.
  • The cross blade has many teeth and a small esophagus, which results in a very smooth and concise cut.
  • The combination of blades is more of a universal blade that is between tearing and cutting for a broader range of tasks.
  • Plywood blades have more teeth than crosses, which helps to remove fleas and frayings, which are typical for plywood, resulting in a smoother, cleaner, unusual cut.
  • Thin grinding wheels are designed for more comfortable cutting without large amounts of waste. Kerf is the size of the slit blade cuts in the material.
  • The grinding blade is covered with coarse materials so that it can cut through tiles, masonry, and steel. Each leaf type has different properties that allow it to do its best with specific tasks:
  • The variable spade blade has a different TPI (tooth per inch) in various places. For example, it can have a 10/14 slope rating, which means that it ranges from 10 to 14 TPI. This variable range reduces vibrations and allows faster cutting, allowing use in a broader range of materials.
  • The conical blade is not on the edge of the material for diving cuts where the reciprocating saw begins to cut directly on the surface – so that it is tapered to dive straight inwards.
  • Individual blades are designed for specific materials and are suitable for non-specialists to choose the best blade without much knowledge simply.
  • The two-way blade has teeth that cut in both directions, allowing the blade to cut both thrust and tensile movements, resulting in faster cuts. It is not suitable for all works, but works best for materials such as plaster, for example.

Can I cut through the tree branches with a reciprocating?

Reciprocating saw is comparable to a jigsaw that was not designed to complete the work, but for the demolition or quick cutting work that may not be pretty, but is simply done quickly and correctly. It is not only a demolition saw but also a large as a sealing saw, a tube cutter, drywall, and a sewer cutter.

Many saws can be used for cutting trees, but if you are responsible for the work of cutting several thicker limbs or branches, you will want a tool that is specially equipped for this work – like a reciprocating saw.

The regular benefits of using a reciprocating saw, unlike other types of saws, revolve around their overall flexibility. They are much more comfortable and safer than a circular saw for work. Which must sit on a ladder, can work in narrow and narrow areas or behind solid materials, where other reciprocating saws do not fit, they do a great job of cutting holes or cracks in the middle of drywall or sheets. They will make hunting cuts around adjacent materials such as the breeze.

So let’s go back to pruning the branches of trees – the answer to this question is yes. Reciprocating saw is one of the best saws for cutting branches or felling small trees. You can use a regular saw blade to cut tree branches, but the reciprocating saw only works as well as the blade designed for a particular project – as the cutting disc.

Many different reciprocating saws work well for your needs, such as the DEWALT Bare cordless reciprocity saw, or the BLACK-DECKER BDCR20B 20V circular saw. An excellent example of a right blade would be a 12-inch 4/5 TPI cutting wheel, designed to provide cleaner and faster woodcutting, with a thin edge for greater flexibility.

What you need to do is put on the glasses, put the cutting disc in the reciprocating saw, turn it on, and see it. That’s it! The work is done in a few seconds, and it cuts your tree branches as if they were butter.

Can a reciprocating saw cut down trees?

While deciding what type of reciprocating saw to use to felling trees, there are many variables to consider: one kind of tree (or tree) that you want to fall, and two: how to experience each other’s saws. Using a chainsaw is probably the best way to cut down large trees, mainly hardwood because they are made for it. Make sure you have the right chain.

However, you really shouldn’t try to control a chainsaw on a massive tree unless you’re damn experienced – they’re on the most critical electrical tool that exists, and you can cripple or even kill it in seconds. So if you don’t know what you’re doing, it’s much better to find someone to do it.

This means that it may not be huge trees, but soft pine trees or smaller trees that you want to clean. Now your work is much safer and easier to manage. Reciprocating used with the right blade for this task can provide a more reliable and more successful way to fall from smaller trees with a little patience and know-how.

Much lighter and smaller than a chainsaw, the use of a reciprocating saw also makes it easier to cut these upper branches. Also, make sure that you use a blade that is made to cut wood. A good example would be a 12-inch 4/5 TPI cutting disc that was made to create a cleaner and faster cut through wood, with a thin edge for the best flexibility.

How do I use the reciprocating saw?

Known as the “Swiss Army Blade,” the reciprocating saw is designed for various cutting tasks around the house and on the construction site. If you don’t currently know how to operate the reciprocating saw, you should do it because if you do, it will probably be all you need.

The reciprocating saw, or saw, as many call them, has many hats: it is a demolition saw, a finely cut saw, a minimal surface saw, a pipe cutter, drywall saw, and a pipe cutter. It is even a large tree cut and a small tree cutter.

The fact is, if you’ve learned the secrets of what this reciprocating saw will do, you’ll want one. Then it’s just a matter of deciding which saw reciprocating brand, and later on the blades, you need to do your homework. From there, it includes a choice of different sizes, patterns, whether you want wired or wireless, running, and weight of the tool. And then there are other considerations in which you have to consider yourself up, like, reverse the blade cut or down ?

Does that look like a handful? How comfortable is the handle? How big is the saw, or how the light? Modern technology from reciprocating manufacturers has improved this tool over time with tremendous progress, especially over the past decade.

Faster cuts, more power, variable speed, a smaller size, a lower weight, better housing, even one-handed reciprocating saws, all at an affordable price that makes this powerful little tool even more valuable.

For cable winches, a higher amplifier is enough for most jobs, and all that more than 12 amps will do well. If you prefer a wireless reciprocating saw (or battery), today’s models will amaze you with their robust and durable lithium batteries, many of which provide up to 50 percent more work performance and 50 percent more battery life. They are also better equipped to cope with extreme temperatures and cold.

Other factor to consider is the length of the distance. The blade travels in the first shot may vary depending on the size of the saw. The long reciprocating saw will cut faster, but it needs more willpower to do its job, and more amplifiers to drive the blade. Typically, the long-aVC model covers additional demolition work and a shorter dashboard for more sensitive and accurate work.

The orbital reciprocating saw adds oscillation or back-to-back movement to regular reciprocity, which adds a slight upward movement to the cut, resulting in an oval cut that is best for wood. The short and saw allows you to get to tighter places where other saws can’t reach. A heavier reciprocating saw reduces vibrations a little more than light saws. However, you may prefer a lower weight. It all depends on your comfort.

If vibrations are a problem for you, look for models with AVT- anti-vibration technology. For example, MAKITA is known for its AVT models. Now that you have a little experience in saw reciprocating and you know what you want, we’ll learn how to deal with it.

How do I use the reciprocating saw?

Choose the right blade

Having a reciprocating saw for this work is the right tool, but if you don’t have the correct sheet, it will immediately be a wrong tool. Choosing the right blade for each project offers the best experience. Of course, there are some different blades to reciprocating the saw, but doing homework before choosing will make a difference.

If you don’t know which blade to arrange for the project, we recommend starting with a specific blade to the given material.

For example, if you work with steel, select a blade specially designed to work on steel projects. There will still be many options, but the selection in this category will shrink them.

Put the blade in the lining

Make sure the tool is disconnected first, or remove the battery in the wireless models, and then insert the blade. Almost every reciprocating saw on the market today has a tool-free clamping system that simply works around a quarter or half rotation to release and insert the blade.

On-site blades may return the feed to its original position. It is always good to give the blade a small tug to ensure that it is attached to the lining before commissioning. If you remove the blade that has just been used, use gloves to remove it as it will be hot.

Know how your cut works before you start

Once the reciprocating saw comes into contact with your material, focus on how it cuts – but the blade will be well beyond the cut. Make sure your blade doesn’t hit anything else in its path when it moves quickly back and forth from the farthest point. This is particularly important to consider when cutting into the drywall where you can not see what is on the other side of the drywall. It is vital to check power lines, plumbing, etc. before you start.

Know your speed

Once you get an idea of the speed of your reciprocating saw, it will be more intuitive. Before you make the main cut, make a small cut slowly to see how it responds to the material with speed and torque. This will help you take more control over most of the work. As the blade approaches the cutting output, you should slow down.

The shoe is right to have

The shoe is like the nose of a reciprocating saw – its flat surface serves as a base and serves several purposes. Many shoes can be adjusted to move forward or backward to extend the life of the blade, but a shoe that stops is also essential. The shoe works to stabilize the saw and material. If you press the shoe against the material you are cutting, you will notice that the vibration of the saw will decrease considerably.

If you cut the material too flat, you will see an increase in the vibration of the saw and the equipment itself. Besides, the shoe serves as a pivot point for diving cuts – reciprocating the back end of the saw and working the shoe as a critical point, giving you more control to immerse yourself in the material.

Work with the blade slowly to see the saw in a thicker material

If the blade slowly passes through heavy or durable material and gives you a drive, it can mean several things. Firstly, that the blade is dull and must be replaced; or two, it could just mean that you don’t want the reciprocating saw to do all the heavy reciprocating.

When working with denser material, you need to gently tilt the blade back and forth like a saw to see, and then you will find that the saw progresses faster, as it reduces the load, allowing the blade teeth to focus on a smaller part. We hope you enjoyed these tips!

What types of reciprocating saw blades exist?

Base on the type of project and the cutting material, there are different types of discs that can be used with a reciprocating saw. For instance, there is a fine-tooth blade that looks like a hack saw, which is used to cut metal pipes and nails; The rough blade is to cut wood; coarse blade on plaster, and the “toothless” stone cutting blade and are covered with a unique abrasive grain.

The more you use your reciprocating saw, the more you know about how it works and what you can achieve with it. Then you have more confidence in choosing a blade that will do a specific task. You will find that you can use the sheet type for different projects, depending on how this particular blade works. For example, you can use a nail-cutting blade to work with shingles or plywood.

Most reciprocating saw blade sizes range from three to 12 inches in length, but the default size is six inches. There are also types of jigsaws available. 12-inch blades that are useful for entering deeper crevices or even cutting thicker wood. Although they are hard, these blades are not indestructible. On the contrary, they are disposable and should be replaced if you notice that they become blunt and slow down work.

Teeth: The tooth per inch (TPI), combined with the size of gulet – this is the depth of the space between the teeth, and notch – the crack made by the blade, all determines the material that can cut the blade.

  • Low TPI blades provide faster cuts and coarser edges, ideal for wood.
  • Blades with high IPT provide smooth and slow cuts, perfect for metal, read our guide to the ideal metal cutting tool.
  • The number of IT varies from 3 to 24.
  • To reduce the catch, try to let at least three teeth come into contact with the material at any time.

There are three facets of the reciprocating saw blade to consider: length, thickness, and width.

  • The longer the blade is, the deeper the cut.
  • The full blade reduces bending and fluctuating.
  • Heavy blades are usually 7/8 inches wide and 0.062 inches thick.
  • 035-inch blades provide sufficient strength for standard cutting.
  • 05-inch blades offer increased stability.
  • Small blades with tapered backs are suitable for cutting.

To extend the life of the blade, you can try to hammer the blade when it is bent. You can also try a small trick by snapping the tip at an angle with some can that has a sharper blade. Be sure to size safety glasses.

Below are the different types of reciprocating saw blades that are currently on the market:

  • Carbon steel as the most common blade, it is ideal for cutting softwood and plastics, but it will quickly become annoying with hardwood and other hard materials. These are flexible to allow bending without breaking.
  • Bimetallic blades are glued to tool steel teeth and remain soft longer, surpassing standard carbon steel blades with faster cutting, but they are more expensive.
  • Carbide tips are the most common bimetal saber saw blade, and they work great for harder cuts.
  • High-speed steel blades are more expensive than carbon steel, but are also much harder and will allow you to cut hardwood without stump so quickly. Makes the best choice as a general-purpose: durable blade that lasts five times longer than carbon steel. These blades have permanent teeth, but are more prone to breakage.
  • Carbide-grit blades are abrasive blades that are made for harder materials, such as marble, ceramics, cement board, and fiberglass. This is the most common type of alternative coarse blade and had a coating that varies from medium to heavy.
  • Diamond blades have real diamonds built into the tips and are used for cutting glass, ceramics, and concrete. Six types of blades are made for specific tasks :
  • The tearing blade has a larger esophagus (the area between the teeth) and several teeth that remove wood quickly and efficiently, making a rough cut.
  • The cutting blade has a lot of teeth and a small esophagus, which produces a very smooth and concise cut.
  • The combined blade is instead a universal blade, which is located between the ribs and cross cuts, for a broader range of tasks.
  • Plywood blade has more teeth than crosses, which helps to remove the chopping and chipping of plywood and make a smoother and cleaner cut.
  • Thin cutting sheets are for easier cutting without too much waste. The edge is as significant as the groove blade cuts into the material.
  • The grinding blade is covered with a coarse material so that you can cut tiles, masonry, and steel.

Leave a Comment